Jump to content

canadiancrawler

Members
  • Content count

    262
  • Joined

  • Last visited

Community Reputation

2 Neutral

About canadiancrawler

  • Birthday 09/07/1961

Contact Methods

  • Website URL
    http://
  • ICQ
    0

Profile Information

  • Gender
    Male
  • Location
    Petitcodiac,NB
  • Interests
    4wheelng,going to hockey games,getting Bombed,quading,camping,traveling
  1. canadiancrawler

    stalling intermittently

    Ok update Purchased vp44 and installed it last week,which was a little cold on the fingers doing it outside as we still have 2 to 3 feet of snow in the yard and only had highs of 4 last week. Anyhow got it done and fired it up and HOLY COW it started and ran smooth took it for a drive and evrything seems to be fine.So will see how things go once i start driving it regularly. Did alot of searching to find a pump,with the cdn $ the way it's been there was no point in me trying to get one from south of the border so i asked around and there is a local guru that is doing cummins conversions into fords and he was very helpful and got me one rebuilt of course but with new PSG $1600 which would have been more for me to get one and pay shipping and all the other costs to get it acroos the border. Took my time putting it in to make sure key lined up properly,especially since this was the first time i have attempted something like this,but with the confidence that i got from being at so many Bomb parties and the help from eveyone there on all my other trucks i jumped in and did this. A little scary to start especially being on the other side of the country away from any help from friends. So thanks everyone for the help and the boost. Lee
  2. canadiancrawler

    stalling intermittently

    Ok,i cleaned the map sensor and the iat sensor.Hooked up a fuel pressure guage to the injection pump at the schrader valve.started truck and fuel pressure guage in truck reads 19psi guage on injection pump was jumping between 12 and 16psi,when i give it some throttle guage in truck goes down to 14 and guage on inj pump goes down to 8.When i shut the truck down the guage on the inj pump didn't hold pressure(should it) guage in truck stays at pressure until i go to start the truck again then it goes to zero when i turn key on start truck it builds pressure like i assume it is suppose to.question is shouldn't the guages read the same pressure?or am i wrong because they are reading in different spots? Thank-you
  3. canadiancrawler

    stalling intermittently

    unhooked edge ez to see if that might have anything to do with it and other then less power i still had hesitation.so more testing to come when i get more time to work on it.
  4. canadiancrawler

    stalling intermittently

    OH yeah and I tried to check the setting on the Apps and I got a reading of zero again,so I don't know what is going on there,I did read somewhere that you are suppose to use a analog multimeter and mine is a digital.
  5. canadiancrawler

    stalling intermittently

    ok ,got a piece of clear tube hooked up to check for air took for drive,opened her up about 90mph a few times and no air bubbles and no stumbling.Went home put new hose piece on,just because.took kid to dance class went for drive opened her up again and nothing happened,Went home,about 15min later got in truck to go get kid and just driving from home to arena approx. 2miles maybe stumbled half a dozen times,Got kid headed home and drove fine on the way home. So iguess with what everyone is saying it must be the inj pump or could it be.Other varibles electrical maybe?????? Thanks
  6. canadiancrawler

    stalling intermittently

    Yes we did clear it. Thanks
  7. canadiancrawler

    stalling intermittently

    Ok got the codes read today and came up with P1693 and po122 which said it was a tps low voltage and that was it.So I don't understand that one, TPS was set according to directions.P1693 just means there is a code to be read.It did drive fine into town and back but I didn't get on it either,i did pick up some clear hose to check to see if there is air getting into the system.Biggest thing is I only get a couple days a week to work on it.so it does take awhile to do these things. Thanks
  8. canadiancrawler

    stalling intermittently

    apps set at .68. haven't gotten a code reader yet,don't take the truck into town,so i guess when i get a chance to take it to town i get that done. I have electrical cleaner so i can use that and then put diletic grease on it. thanks.used truck today to go help with atv club shack repair and it drove fine,never got on it and idle at 19 psi and driving down road 16/17 psi. thank-you
  9. canadiancrawler

    stalling intermittently

    ok,i run ddp 50hp inj,edge box on number 3 except when towing.i will try and clean the connections already did most of them but missed the ecm,so i will try and get that one. thanks
  10. canadiancrawler

    stalling intermittently

    I don't know how do i test that?How do i know if the pump is pumping enough? Thanks
  11. canadiancrawler

    stalling intermittently

    just doing some reading online and never thought of this but could it be when i step on it the fuel goes to the back of the tank and i m not getting enough fuel for the pump?i just have a ddrp mounted in stock location.just a thought.
  12. canadiancrawler

    stalling intermittently

    so went for a drive this morning and i could cruise down the road at 60mph.I did notice though that my fuel pressure was only at 14 and idle was 15 when i stepped on it it went down to almost 4,so i didn't do that again.did also notice a stumble.So came home and took fuel pump out and pulled spring put back together took for drive pressure at 20 idle and down to 10wot,still has that stumble/hesitation when stepping on it.have apps set.when talking to tim,didn't get much from him and didn't even return my last question,so don't think i will get much help there.So how do i check if the IP is working properly or is there a way i can do that? Thank-you
  13. canadiancrawler

    stalling intermittently

    .580-.700 had mine set at .660,so don't know why it is zero now.contacted tim but haven't heard back from him yet. thanks
  14. canadiancrawler

    stalling intermittently

    well i get a reading of zero on the multimeter,don't know why had it set when i put it in,but i can't get it to do anything on the meter. Stumped
  15. canadiancrawler

    stalling intermittently

    Well i will get into it today and see if i can find anything,the new apps is from Tim order online from his site.So i will do that.It not doing the same thing it did before,it is like a complete lose of power n pedal.But i will go from here n see what happens. Thanks
×