[19Kgvw]

NWDave commented on starting a work list a few days ago......so.....I'll start.

I'm going to do:

KDP (I know....it's about time :bl: )
finally fix my tail gate latch....it's been....oh.....5 years...not that I'm counting :hit:
hopefully look for a vacuum leak off the booster cuz my brake idiot light comes more than I like

I should have all the tools I'll need - moral support is always needed though :p:

what else is out there???

[Firstgenfanatic]

Rich, I have fan wrenches you can use for your KDP project. You won't be the only person there opening up the front timing cover......I need to reseal mine. I have a new Cummins gasket for it and "Right Stuff". I also will be doing the usual 1st gen pump tweaks (full fuel screw & 1/8" timing bump). I will probably need the "S" wrench for that. (whoever has one?) So far, that's it on my plate.

[19Kgvw]

Firstgenfanatic, on 27 January 2010 - 06:35 AM, said:

Rich, I have fan wrenches you can use for your KDP project. You won't be the only person there opening up the front timing cover......I need to reseal mine. I have a new Cummins gasket for it and "Right Stuff". I also will be doing the usual 1st gen pump tweaks (full fuel screw & 1/8" timing bump). I will probably need the "S" wrench for that. (whoever has one?) So far, that's it on my plate.

Yes = you'll enjoy the pump mods. Why is your timing cover leaking?

[NWDave]

Don't forget, when getting elbow deep into KDP's, most will also want to replace their fan belts with bright shiny new ones, since they're there already. I remember a few bomb parties where foreheads were slapped and a mad dash was made to the nearest parts store.

[199712valve]

Perhaps some twins......(they are in the mail!!) :burnout:

[canadiancrawler]

I have S wrenches.
I hope to get air bags put on with some help.:)

Lee

[1stdiesle]

I will bring my air bags and if we have time we can do it other wise no big deal.......

[1 Grumpy]

I'd like too do the kdp if possible but if not no biggy. tweaking the pump and getting a differant aircleaner is a must for me tho....And I'll be there too help anyone...Can not wait thanks Hoss for doing this again oh and you too Terry

[19Kgvw]

1 Grumpy, on 27 January 2010 - 08:11 PM, said:

I'd like too do the kdp if possible but if not no biggy. tweaking the pump and getting a differant aircleaner is a must for me tho....And I'll be there too help anyone...Can not wait thanks Hoss for doing this again oh and you too Terry

no problem with additional help for the KDP - it's appreciated !!

and ditto to our hosts'.... Mark and Terry (Terry's cool cuz she has a 1st gen!! :dance: )

[Firstgenfanatic]

19Kgvw, on 27 January 2010 - 05:48 AM, said:

Why is your timing cover leaking?

Basically when I did my KDP @ Hoss's, no gasket was used on the timing cover. Instead, plain RTV was used to reseal it. The RTV started to fail a few miles ago and the leak has gotten worse. I now have a Cummins gasket and high quality sealant. This should no doubt fix the leak for good.

[Firstgenfanatic]

1 Grumpy, on 27 January 2010 - 12:11 PM, said:

I'd like too do the kdp if possible but if not no biggy.

I can't remember.......did I give you my spare KDP tab when I was at Hoss's for the KDP party?

[Dieselpolluter]

I think i will be bringing the stuff to install my alternator tach, and possibly the pump off the new 92. Need to pull it apart and clean it if anyone would like to get a hands on break down of a VE.

[Dieselpolluter]

I think i will be bringing the stuff to install my alternator tach, and possibly the pump off the new 92. Need to pull it apart and clean it if anyone would like to get a hands on break down of a VE.

[1 Grumpy]

Firstgenfanatic, on 28 January 2010 - 08:09 PM, said:

I can't remember.......did I give you my spare KDP tab when I was at Hoss's for the KDP party?

yeah you did but I can not find it...wouldn't mind getting a tac too where did you get yours Chris???

[Firstgenfanatic]

1 Grumpy, on 29 January 2010 - 02:40 AM, said:

yeah you did but I can not find it...wouldn't mind getting a tac too where did you get yours Chris???

I bought mine through Genos Garage. They can actually order you anything, as long as they carry the brand. Mine is an Isspro 5503. This tachometer is designed to plug into the factory tach harness under the dash.

[Darkside's Callin']

New here, but looking to do the 3200 spring and tweak on the pump a little more, should probably do the KDP also, but will depend on $$ and time.

Also need to troubleshoot my tach, it getting a little flakey lately, read 3-400 rpm low, then works good.

Looking forward to meeting people and getting ideas for the truck.

Wife just yanked the leash, Kids B-day party is that day, So I'll have to wait for the next one...

This post has been edited by Darkside's Callin': 30 January 2010 - 05:38 PM

[Mike G]

Would anyone be interested in helping with a 3200 gsk and fuel screw? Any help would be greatly appriciated thanks.

[Braeden12v]

a 1st gen right

[Mike G]

Braeden12v, on 30 January 2010 - 08:40 PM, said:

a 1st gen right

yup!

[Firstgenfanatic]

Mike G, on 31 January 2010 - 05:56 AM, said:

yup!

Mike G,
I have done several of the 3200 gsk installs. I would be happy to help during the party.